Can someone translate this to english? This is in Eola S6- T2S- R3E

  

 

UTMX 83 UTMY 83 LONGITUDE 83 LATITUDE 83
575313.04042349 3419601.13706432 -92.21187413 30.90735907

BOTTOM HOLE COORD

EFFECTIVE DATE END DATE PLUGBACK TOTAL DEPTH TRUE VERTICAL DEPTH MEASURED DEPTH LAT DEG LAT MIN LAT SEC LONG DEG LONG MIN LONG SEC COORDINATE SOURCE LAMBERT X LAMBERT Y ZONE COORDINATE SYSTEM
07/22/2011 8900 0 0 0 0 0 0 02

WELL HISTORY

SERIAL WELL NAME WELL NUM ORG ID FIELD ST CD PT WELL CLASS EFF DATE END DATE STAT DATE
243577 R R IRION 001 S229 3648 01 00 07/22/2011 07/22/2011

SCOUT INFO

REPORT DATE WELL STATUS MEASURED DEPTH TRUE VERT DEPTH DETAIL
08/08/2011 05 8900 DRLD T/ 8900'; REVIEWING CORES;
08/02/2011 05 3760 DROVE 16" T/ 40'; SPUD 7/28/11; RAN 8-5/8" T/ 1537' & CMT W/ 455 SXS; TSTD BOPS 7/30/11; DRLG @ 3760'; (BOP INFO: SHAFFER LWS, 11", 3000 PSI);
07/22/2011 01 8900 S 24 D 03' 33" W - 19,908.04' FROM NGS MONU. "865" IN SEC 6.

Views: 250

Reply to This

Replies to This Discussion

07/22/2011 - S24 D 03' 33" W - 19,908.04' FROM NGS MONU. "865" IN SEC 6. -Permitted date and surface location in degrees, minutes, seconds from a Monument located in Section 6.

 

08/02/2011 - DROVE 16" T/ 40'; SPUD 7/28/11; RAN 8-5/8" T/ 1537' & CMT W/ 455 SXS; TSTD BOPS 7/30/11; DRLG @ 3760'; (BOP INFO: SHAFFER LWS, 11", 3000 PSI); - Drove 16" surface casing to 40', Drill bit hit the dirt on 7/28/11, Ran 8 5/8" casing to 1537' and cemented with 455 sacks; Tested Blow Out Preventers on 7/30/11, Drilling @ 3760';  Blow Out Preventer specs.

 

08/08/2011 - DRLD T/ 8900'; REVIEWING CORES;  Drilled to 8900', took a core sample.

 

IANAD. Disclaimer: I An Not A Driller.  LOL!

Skip, the 16" would be the conductor pipe while the 8 & 5/8" would be the surface casing.

 

By the way NGS is National Geodetic Survey. 

Thanks, Les.  In what situations are NGS monuments utilized?
Good lesson Skip
How can a location be 19,908.04 feet from a monument located in Sect 6 and still be in Section  6? It is a pretty much standard section 1 mile by 1 mile. And thanks for the reply.

Monuments are used in land surveying.  It would be used for section control.

Sorry for not being more specific.  Yes I understand the use of monuments in land surveying.  I am wondering why the usual surface location description based on distance from section lines is replaced with this description utilizing the monument.
Well that monument is roughly 3+ miles away ...that couldn't have been in the same section..
A lot of the wells in South Louisiana use this type of description. The monument isn't in Section 6 it is  somewhere else.

Skip,

 

I think they use the NGS monuments in south Louisiana because of the irregular sections.

That would be a good reason.  I was also wondering whether there might be historic Arpent tracts with a standard governmental section overlay.
The reason South Louisiana has irregular sections is that the arpent land grants were treated and numbered as PLSS sections. I have not seen any PLSS theoretical sectioning overlays for South Louisiana. At this point it would most likely be confusing and conflict with old records.

RSS

Support GoHaynesvilleShale.com

Not a member? Get our email.

Groups



© 2024   Created by Keith Mauck (Site Publisher).   Powered by

Badges  |  Report an Issue  |  Terms of Service