Replies to This Discussion

Permalink Reply by Skip Peel - Mineral Consultant on December 19, 2010 at 15:25

Test results are reported in their on section of SONRIS well files.

 

SCOUT INFO

REPORT DATE	WELL STATUS	MEASURED DEPTH	TRUE VERT DEPTH	DETAIL
04/29/2010	10	16316		COMPLETED 1-29-10; GAS; HAYNESVILLE RA; 8475 MCFD; TRACE CONDENSATE; 17/64 CHOKE; 49.9 GVTY; 6850# CP; PERFS 11,965-16,120'
12/14/2009	09	16316		TD 12-11-09; SET 4 1/2 & 5 1/2 TO 16,316' W/ 645 SX
12/08/2009	05	14230		DRILLING
12/04/2009	09	16316		SET 4 1/2 & 5 1/2 TO 16,316' W/ 645 SX
11/30/2009	05	11800		SPUD 11-8-09; SET 10 3/4 TO 1860' W/ 700 SX; SET 7 5/8 TO 10,858' W/ 870 SX; DRILLING
10/02/2009	01	13000		297' FSL & 848' FWL OF SEC 1. PBHL: 660' FSL & 848' FWL OF SEC 1.

PERFORATIONS

SERIAL NUM	COMPLETION DATE	UPPER PERF	LOWER PERF	SANDS	RESERVOIR
240282	01/29/2010	11965	16120	HA	RA

WELL TESTS

RPT TYP	TEST DATE	RPT DATE	OIL POT	COND	GAS DEL	WATER	BSW%	FLOW PRES	SHUTIN PRES	CHOKE	UPPER PERF	LOWER PERF	BOT HOLE PRES
DT-1	09/15/2010	11/01/2010			4810	65		70		16	11965	16120
DT-1	04/20/2010	05/01/2010			7250	115		5350		17	11965	16120
SDM2G	02/11/2010	02/11/2010			8475	450	.2			17	11965	16120

• ▶ Reply

Permalink Reply by Les Bamburg on December 19, 2010 at 17:32

Missy, you can find the potential information by accessing the following on Sonris Lite:

"Document Access" then "Permitting" then "Well Allowable/etc".

• ▶ Reply

Permalink Reply by Mac Davis on December 19, 2010 at 21:20

If you have a particular well, I'll see if I can provide a direct link.  The format will be something like

 

http://sonlite.dnr.state.la.us/sundown/cart_prod/cart_con_wellinfo2...

 

The number on the end is the well number.

• ▶ Reply

Permalink Reply by Missy on December 22, 2010 at 11:46

Mac,

The well #'s are 240524 and 240967. Thanks Ya'll.

• ▶ Reply

Permalink Reply by Mac Davis on December 22, 2010 at 12:08

Just put the number for your wells on the end.  Are these correct?

 

http://sonlite.dnr.state.la.us/sundown/cart_prod/cart_con_wellinfo2...

http://sonlite.dnr.state.la.us/sundown/cart_prod/cart_con_wellinfo2...

 

Even though the wells have been potentialed, they haven't put the data on the SONRIS page.  I've seen this before, sometimes waiting a couple of months before the data shows up.  I don't know if this is the state's fault, the operator, or some combination of both.

 

I don't know if there's somewhere else to look it up. 

 

It will eventually show up under "well allowables."

• ▶ Reply

Permalink Reply by Les Bamburg on December 22, 2010 at 12:38

Mac, It is due to the State's delay.  Too much well activity for too few people to be able to keep up with the work.

• ▶ Reply