Where do I find the state potential information on wells?  Merry Christmas and Happy New Year!

Views: 106

Reply to This

Replies to This Discussion

Test results are reported in their on section of SONRIS well files.

 

SCOUT INFO

REPORT DATE WELL STATUS MEASURED DEPTH TRUE VERT DEPTH DETAIL
04/29/2010 10 16316
COMPLETED 1-29-10; GAS; HAYNESVILLE RA; 8475 MCFD; TRACE CONDENSATE; 17/64 CHOKE; 49.9 GVTY; 6850# CP; PERFS 11,965-16,120'
12/14/2009 09 16316
TD 12-11-09; SET 4 1/2 & 5 1/2 TO 16,316' W/ 645 SX
12/08/2009 05 14230
DRILLING
12/04/2009 09 16316
SET 4 1/2 & 5 1/2 TO 16,316' W/ 645 SX
11/30/2009 05 11800
SPUD 11-8-09; SET 10 3/4 TO 1860' W/ 700 SX; SET 7 5/8 TO 10,858' W/ 870 SX; DRILLING
10/02/2009 01 13000
297' FSL & 848' FWL OF SEC 1. PBHL: 660' FSL & 848' FWL OF SEC 1.

PERFORATIONS

SERIAL NUM COMPLETION DATE UPPER PERF LOWER PERF SANDS RESERVOIR
240282 01/29/2010 11965 16120 HA RA

WELL TESTS

RPT TYP TEST DATE RPT DATE OIL POT COND GAS DEL WATER BSW% FLOW PRES SHUTIN PRES CHOKE UPPER PERF LOWER PERF BOT HOLE PRES
DT-1 09/15/2010 11/01/2010

4810 65
70
16 11965 16120
DT-1 04/20/2010 05/01/2010

7250 115
5350
17 11965 16120
SDM2G 02/11/2010 02/11/2010

8475 450 .2

17 11965 16120

Missy, you can find the potential information by accessing the following on Sonris Lite:

"Document Access" then "Permitting" then "Well Allowable/etc".

If you have a particular well, I'll see if I can provide a direct link.  The format will be something like

 

http://sonlite.dnr.state.la.us/sundown/cart_prod/cart_con_wellinfo2...

 

The number on the end is the well number.

Mac,

The well #'s are 240524 and 240967. Thanks Ya'll.

Just put the number for your wells on the end.  Are these correct?

 

http://sonlite.dnr.state.la.us/sundown/cart_prod/cart_con_wellinfo2...

http://sonlite.dnr.state.la.us/sundown/cart_prod/cart_con_wellinfo2...

 

Even though the wells have been potentialed, they haven't put the data on the SONRIS page.  I've seen this before, sometimes waiting a couple of months before the data shows up.  I don't know if this is the state's fault, the operator, or some combination of both.

 

I don't know if there's somewhere else to look it up. 

 

It will eventually show up under "well allowables."

Mac, It is due to the State's delay.  Too much well activity for too few people to be able to keep up with the work.

RSS

Support GoHaynesvilleShale.com

Not a member? Get our email.

Groups



© 2024   Created by Keith Mauck (Site Publisher).   Powered by

Badges  |  Report an Issue  |  Terms of Service