landowner

Grizzlies DU #1H

Hi All,

If you have a few moments, please share any info and projections if any for the Grizzlies DU #1H, Exxon/XTO (Haynesville Shale) Nac Co., YBARBO; (as opposed to the Grizzly in San Augustine County).

The Grizzlies DU pad site has to 2 big vertical tanks, 2 horizontal propane type tanks with an exhaust, and another station with a digital readout of 8.5 (as I recall) that appears connected to the new pipeline running east/west parallel to the pad.

I read earlier today on GHS that a well can produce but may not be completed. What does that mean?

I appreciate any and all comments!

Views: 2687

Replies to This Discussion

Permalink Reply by jffree1 on April 5, 2012 at 2:13

Aggies Unit is mostly in San Augustine County but a small piece of the unit is in Nacogdoches so that could be correct.


landownerPermalink Reply by Becky on April 5, 2012 at 16:09
Is the Aggies anywhere near the Texans and Grizzlies unit or near the Longhorns and Sun King unit? If not I had the wrong unit name. Are the Texans and Grizzlies right next to eachother?
Permalink Reply by jffree1 on April 5, 2012 at 17:31

Grizzlies begins the furthest west (FM 95 @ 21) with Texans on its east boundary.  Then Sun King is south of Texans and Longhorns is east of Sun King.  Aggies adjoins Longhorns to the east.  


landownerPermalink Reply by Becky on April 8, 2012 at 4:00
Are there any permits for the Aggie Unit? Is there a map that shows unit names and wells.
Permalink Reply by jffree1 on April 8, 2012 at 5:07

Becky, see if these help.  You can see the unit plats on the well permit page on RRC.  I just take those plats and overlay them on Google Earth.  If you need help with finding permits go to the RRC Help group where you will find instructions.

http://www.gohaynesvilleshale.com/group/trrchelpcenter

Attachments:

landownerPermalink Reply by j garrett on April 8, 2012 at 13:10

That's a slick trick jffree1. How did you get the proper scale and how do you handle transparency?

Permalink Reply by jffree1 on April 8, 2012 at 13:41

You can adjust the transparency of the overlay in "properties" on GE at any time.  I just make sure I have at least one well located and then I just use the landmarks (roads, creeks, etc...) and tract boundaries and keep dragging the sides in and out until the plat matches what you can see on GE.  It's not precise but it's pretty darn close most times.  You can always check the scale by using the well lateral length and checking the overlay with the ruler tool to see if you have it close to what is on the original plat.


landownerPermalink Reply by Becky on April 22, 2012 at 16:04
Does anyone know when we might see a first check from the Texans du #1H or the Grizzlies du#1H?
Permalink Reply by v on May 5, 2012 at 13:45

I have the lady's name and phone no for XTO. I will give her a call Monday and see what she has to say. If its not a good response I will post her no.  and everyone can call her.

Permalink Reply by jffree1 on May 5, 2012 at 15:01

"I will post her no.  and everyone can call her."

LOL!!  That may turn out to be an effective "remedy" to XTO's disdain for their mineral owners (if she gets enough phone calls).

Permalink Reply by v on May 7, 2012 at 11:06

Left a message today and have not got a call back yet.


landownerPermalink Reply by Becky on May 7, 2012 at 13:42
While we r waiting on the Grizzlies and the Texans... any better numbers from the Longhorns?

RSS

© 2026   Created by Keith Mauck (Site Publisher).   Powered by

Badges  |  Report an Issue  |  Terms of Service