Early Haynesville Shale horizontal wells were allowed spacing for eight wells per section. Over time operators moved to six wells and now, depending on area and level of development, five and sometimes four wells per section. In the southern half of the Louisiana fairway where there is economic Mid-Bossier in addition to Haynesville Shale, the wells per section can be doubled. Much of the RBN article is attempting to describe wells in both the Haynesville and the Permian plays when covering well spacing. The Haynesville has only the two benches (landing zones), Haynesville and Bossier, while the Permian and other basins may have more benches making well spacing more complex.
Drainage Areas, 3D Analysis Can Improve Well Spacing and Production
Tuesday, 11/17/2026 Published by: Jason Lindquist https://rbnenergy.com
Excerpt. Link to full article: https://rbnenergy.com/daily-posts/blog/drainage-areas-3d-analysis-c...
Shale producers have become very good at drilling longer laterals and squeezing more wells onto a pad. But there’s a catch: longer laterals and tighter well spacing can boost production, but crowding too many wells into the same rock can leave them chasing the same barrels. The challenge is figuring out how much reservoir each well has to itself, how neighboring wells affect its performance and where additional drilling starts delivering smaller returns for the investment. In today’s RBN blog, we explore how drainage areas help explain those underground interactions and how producers use them to balance well spacing, completion intensity and recovery to improve the economics of shale development.
Let’s start with some basics about hydrocarbon formations and how they’re drilled. As we noted near the beginning of the Shale Revolution in Tales of the Light Sand Laterals, vertical or directional drilling is old school. You do the seismic analysis, mark your “X” on the map, send in the rig and drill straight down. Unlike a conventional vertical well, a horizontal well eventually follows a curved path to enter the target formation and then extends laterally through it, as shown in Figure 1 below. Over time, much longer laterals have been developed, some of which now stretch to three or four miles. Longer laterals can boost a well’s estimated ultimate recovery (EUR) and improve drilling economics by reducing the number of wells needed to access large swaths of a formation, reducing capital costs associated with drilling, drilling pads, pipelines and all the other associated surface equipment (see Follow That Dream).
A major challenge of shale production is deciding how close the horizontal wells should be to each other to maximize EUR. For years, shale producers have used a handful of measures to show how intensively they are developing an oil or gas field. The most common is wells per section, with a section equal to 640 acres. An operator might drill eight, 12 or even more wells across that area. A related measure is acres per well, which simply shows how much land is available to each well on average.
Another important metric is the spacing between horizontal wells, usually measured in feet. Tighter spacing allows more wells to be drilled in the same area, but putting wells too close together can cause them to interfere with one another (more on that in a bit). Because horizontal wells have become much longer, analysts also look at total lateral feet per section. This shows how much horizontal wellbore is being placed in a given area and provides a better comparison when one operator is drilling 5,000-foot laterals and another is drilling 15,000-foot laterals. More recently, producers have added measures of completion intensity, such as pounds of proppant or gallons of fracturing fluid pumped per foot of lateral.
These measures are important but increasingly seen as incomplete when it comes to assessing how a well’s performance is impacted by the wells that surround it. Each well has what’s known as a drainage area, which is the portion of a reservoir from which each well draws the oil or natural gas it produces. In Figure 2 below, each wellbore is represented by a black dot, with the drainage area for each well’s horizontal lateral defined by the colored lines that surround it. (This is a view from the side of several horizontal laterals.)
Finding the right approach to well spacing is challenging but critically important. If the wells are drilled too far apart, oil and gas production is not optimized. But if they are too close, they can draw oil and gas from the same areas, resulting in a less efficient drilling program. As shown in Figure 3 below, the drainage areas for the three drilled wells (black dots) are close enough that they are essentially competing for the same pore space. The drainage area for the well in the middle (yellow section) is overlapped by the drainage areas for wells to its left and right (red and blue areas, respectively) and has only a small area of pore space to itself.
Tags:
459 members
240 members
257 members
442 members
302 members
© 2026 Created by Keith Mauck (Site Publisher).
Powered by
GoHaynesvilleShale.com is where mineral owners, landowners and oil & gas professionals discuss the Haynesville Shale, Austin Chalk, Terryville Complex, Tuscaloosa Shale, Lower Smackover Brown Dense and lithium plays. Ask questions, share what you know, and keep up with activity in your parish or county. [ Read More ]