Replies to This Discussion

landownerPermalink Reply by Catfish on July 27, 2009 at 5:30

I did not mean to sound like I was complaining, just hoping for better. Would chk or hk done any better? Has samson had much experience in this play?

• ▶ Reply

Oil & Gas ProPermalink Reply by Skip Peel - Mineral Consultant on July 27, 2009 at 5:40

Catfish. This was SC's first horizontal HA completion in NW. LA. And the Flowing Pressure on this well is low (1800). Unfortunately SC is the only operator drilling in this part of the Play at this time. In 17N -11W SC has the Gilmer 22H (Section 22) which TD'ed 7-20 and Gray 27H (Section 27) which should be building its curve about now. In 18N - 11W SC has the Hall 34H which TD'ed 5-4 and has not had a status update since it reported waiting on a completion rig on that date. You will just have to wait it out. Good Luck.

• ▶ Reply

Permalink Reply by JM on July 27, 2009 at 6:56

Arent both Petrohawk and Chesapeake presently drilling this far North and even 18N? Would this one well give them pause and rethink their drilling plans?

• ▶ Reply

Oil & Gas ProPermalink Reply by Les Bamburg on July 27, 2009 at 5:59

Catfish, as has been stated this is a fairly decent rate for the initial horizontal well in this part of the play. The rate is comparable to the early wells in East Texas and can improve with more experience.

Samson, Deltic Timber 12 #1 Well, Serial #239201, S12-T17N-R11W, Bossier Parish, 4200 Mcfd, 20/64" Choke, 2580 psi Flowing Pressure

• ▶ Reply

Oil & Gas ProPermalink Reply by Skip Peel - Mineral Consultant on July 27, 2009 at 6:08

Les. The Flowing Pressure you quote is from the Scout Info reported 5-19. The 1800 psi I posted was from the Well Test section reported on 7-9. Both calculated on the same choke. Is that a normal variance for <60 days?

• ▶ Reply

landownerPermalink Reply by Checkmateking on July 27, 2009 at 7:12

Looking in the Times this sunday I saw many mediocre wells in great township-range's such as 15N 13W etc.

• ▶ Reply

Oil & Gas ProPermalink Reply by Terry L. Antee on July 27, 2009 at 8:40

Does anyone know how many fracs were done on this well? The number and size seems to make the difference in production according to Chesapeak and Petro Hawk.

• ▶ Reply

Oil & Gas ProPermalink Reply by Skip Peel - Mineral Consultant on July 27, 2009 at 10:33

Terry. The number of frac stages are not always included in the SONRIS Scout Info for a well but the lateral length was right at 4,000'. The average frac stage length for most operators is approximately 300-360'. Eleven would be about normal for this lateral length.

• ▶ Reply

Oil & Gas ProPermalink Reply by Les Bamburg on July 27, 2009 at 11:08

Terry, there was no information regarding number of stages, lbs of proppant, how many stages were successfully pumped, etc. Samson could have had a conservative design for this well.

• ▶ Reply

landownerPermalink Reply by Spring Branch,mineral owner on July 27, 2009 at 11:39

I predict better results from the Gilmer 22, which is 2 miles to the SE of the Deltic Timber well and only 3 miles north of some HK wells that IP'd in the 14-15 Million range. It is a 1st well operator issue IMHO.

• ▶ Reply

Permalink Reply by Taylor on July 27, 2009 at 13:15

Where is the like button? Oh, I forgot, this is GHS not facebook.. joking guys.

SB, I hope you are right about the Gilmer well.

• ▶ Reply