Replies to This Discussion

Permalink Reply by Skip Peel - Mineral Consultant on July 5, 2018 at 11:09

Yes, I have.  It's the very same formation as the Haynesville Shale.  Encana created their Haynesville Shale units using the term, Jurassic, in the early days of the play.  Those unit still have the designation, Jurassic. It's not a different formation as we discussed at length many, many years ago.

• ▶ Reply

Permalink Reply by Todd Parrish on July 5, 2018 at 11:18

Thank you, I have been getting large $$ offers for my minerals in 14n 16w section 19

• ▶ Reply

Permalink Reply by Skip Peel - Mineral Consultant on July 5, 2018 at 11:21

You're welcome, Todd.  Those offers have zero to do with the term, Jurassic.  What they are related to is an uptick in Haynesville Shale development.  When you get large $$$$ offers, please let us know.  That will be of interest to many members.

• ▶ Reply

Permalink Reply by kittycatmama on July 5, 2018 at 16:54

is that in Desoto Todd

• ▶ Reply

Permalink Reply by Todd Parrish on July 5, 2018 at 17:13

caddo 09-14n-16w I think its at the edge of de soto but in caddo 

• ▶ Reply

Permalink Reply by kittycatmama on July 6, 2018 at 14:29

Todd, without naming any companies making offers, what has been your top offer?

• ▶ Reply

Permalink Reply by Skip Peel - Mineral Consultant on July 7, 2018 at 0:45

It doesn't take a professional to conduct basic searches on SONRIS Data Access.  Since surface locations can be, and often are, off the producing unit, the best way to know what section or sections a well produces from is to search by LUW code number.  LUW is a section in every SONRIS Well File.  The six digit LUW number will list all wells producing under that section from a given formation.  However there is another way to know the sections that produces from, the well name.  All HC wells will have two or three numbers, besides the township and range, that indicate the producing sections.  Therefore MCMIN 7&18&19 - 15 -14HC is producing from sections 7, 18 & 19. Your friend is either mistaken or the landman was lying to him.  It is good to help neighbors but only if you know what you are doing.  This is a complicated business.

• ▶ Reply

Permalink Reply by kittycatmama on July 7, 2018 at 3:26

Thanks Jay. I am in GIS now trying to figure it out. Finally found where the bottom holes are noted. This site is so educational. I learned a lot from you and Skip today about figuring out these CULs. Thanks to both

• ▶ Reply

Permalink Reply by Bob Zimmerman on July 7, 2018 at 4:52

< or the landman was lying to him>>>

LOL, God forbid a landman tell a lie. 

• ▶ Reply

Permalink Reply by Skip Peel - Mineral Consultant on July 7, 2018 at 5:09

Anyone who thinks that lying is the stock and trade of professional landmen, doesn't know many.

• ▶ Reply

Permalink Reply by Bob Zimmerman on July 7, 2018 at 8:32

I have known a few, and dirty hands were present. Not all had dirty hands. 

But face it. Dirty hands just come with the oilfield.

• ▶ Reply

Permalink Reply by Two Dogs, Pirate on July 7, 2018 at 10:26

Makes no difference to me, I shake hands with most people, dirty hands or not. I suggest that if you feel that a landman is lying to you then ask to see another landman. I can say that back in the summer of 2008 there were many new hires that didn't know what they were talking about and would have been better just keeping their mouth shut or telling the folks that they didn't know the answer. At that same time there were snakes crawling around that should have been shot or tarred and feathered with no questions asked.

• ▶ Reply

• ‹ Previous
• 1
• 2
• 3
• 4
• Next ›
• Page